home international passport Basic rules for using a spinning reel. Technique for winding fishing line onto a reel How to install a spinning reel on a fishing rod

Basic rules for using a spinning reel. Technique for winding fishing line onto a reel How to install a spinning reel on a fishing rod

OPERATING INSTRUCTIONS FOR SPOTLIGHT COILS

In order to use the reel correctly, carefully read these recommendations!

Spool. Filling the bobbin. Capacity. Removal methods.

Remove the spool and attach the fishing line to it. To do this, unscrew the adjusting screw located in front of the spool or press the button located on the spool (for reels with rear drag). Open the line guide. Place the spool on the axle and tighten the adjusting screw, or, having installed the spool on the axle, slowly rotate in any direction until the spool is in place (for reels with rear drag). Don't use force. An indicator of correct installation of the spool is the click of the spool lock. Close the line guide and begin winding the line. In order for the fishing line to be wound more evenly, tension should be created on the fishing line. For maximum ease of use, the maximum height for laying the fishing line should be about 2 mm from the edge of the spool. The spool capacity of each model for different line diameters is indicated in technical specifications. So that you can use different types fishing line, you need to have additional spools for the reels.

Anti-reverse. Methods and purposes of application.

Anti-reverse prevents the reel head from rotating in the opposite direction when winding the fishing line. Anti-reverse is activated using a switch located at the back of the reel or at the bottom of the housing.

Adjusting the brake mechanism.

The brake mechanism is adjusted using an adjusting screw located in the front or rear of the reel. The braking mechanism is designed to reduce the risk of line breakage in cases of sudden jerks or strong resistance of the caught fish. To adjust the braking mechanism, pass the line through the line guide and thread it through the rings located on the rod. Secure the end of the line. Turn on anti-reverse. Set the rod at a 45 degree angle. Use the adjusting screw to set the required clutch activation threshold. If it reaches the limit, turn the brake adjuster at least a quarter turn back (counterclockwise). When adjusting the brake mechanism, do not use excessive force, as... This may cause the reel or rod to break.

Casting technique.

Take a fishing rod with a pre-attached reel, wound on a spool and passed through the rings (from the handle to the tip of the rod) with a fishing line and a bait attached to the free end of the fishing line in your right or left hand (depending on the subjective anatomical features of the fisherman). Using the index finger of the same hand, press the line two to three centimeters from the line roller to the rod handle. With your free hand, open the line guide arc. Before casting, visually verify that there is no bait on the intended flight path and its subsequent retrieval foreign objects, people and animals . The casting technique depends on a combination of many factors: the length of the spinning rod, the weight of the bait, the presence of obstacles in the casting area, etc. Therefore, it is based on the individual experience of the fisherman. After casting, depending on the type and fishing conditions, reel in the bait. After finishing the wiring, perform the same sequence of actions until the end of fishing or until the fish is caught. Before going out onto the pond, if possible, consult an experienced fisherman.

Care and precautions.

Do not allow sand to get into the rotating parts of the reel.

Keep the reel dry.

The warranty does not cover damage due to misuse or intentional or unintentional breakdown.

Happy fishing!

Also important is the method and features of winding the fishing line onto the reel. The possibility of long casts, the prevention of the appearance of beards on the fishing line, the frequency of accidental discharges of fishing line from the spool, and “shooting” of equipment depend on this.

Rare spinning reel Ming Yang CL/25 CL

This topic will look at how to correctly wind the fishing line onto a reel in order to avoid unpleasant surprises during the fishing process.

Models of spinning reels and types of line winding

Any fishing rod or spinning rod has a reel. There are 3 types of fishing reels. For each of them, a special type of fishing line winding is provided. Since reels have different designs, let’s look at how fishing line is wound on each of the listed types.

Inertia-free reel

The main element responsible for winding the line is the line layer. This is a metal loop with a roller that makes circular movements around the spool when the handle is used. During the first revolution of the spool, the line layer winds the line in one direction, for example, upward, and during the second revolution it winds in the opposite direction of laying. As a result, the line is placed crosswise on the spool.

There are several ways to install fishing line on an inertia-free reel. Each type of reel has its own winding method.

This is the so-called winding taper:

Straight cone. Towards the front side of the spool, the thickness of the laid fishing line decreases.
Reverse cone. The thickness of the line gradually increases towards the leading edge of the spool.
Chaotic winding. The line is wound randomly. This winding method is typical for inexpensive Chinese products.

“Straight cylindrical” winding is obtained by installing two shims

Initially, new coils are configured for cylindrical laying. Then, as necessary, each angler adjusts the laying method to suit himself. The taper adjustment is carried out thanks to special washers located on the spool axis. So, if jerk baits are used for fishing, then winding with a reverse cone is used. In this case, the washer is replaced with a smaller one or removed altogether.

Multiplier reel

The line should be wound onto the multiplier in such a way that there is a gap of about 1-2 mm to the edges of the spool. Since this type of reel does not use backing, it is necessary to accurately calculate the amount of fishing line for winding. That is, it should not be small.

You can thread the cord or fishing line into such a reel in the following order:

The end of the line is threaded through the line guide.
The fishing line is tied to one of the holes in the movable spool. You can also secure the line with a loop by wrapping the line around the spool axis several times.
The reel is attached to the fishing rod.
The line is passed through the right ring.
The friction brake is tightened.
All that remains is to quickly wind the line onto the spool and then put on the leash. In order for the turns to lie tightly, it is necessary to create some tension in the fishing line.

How to create a special knot for tying fishing line on a spool

Inertia coil

The line is laid on an inertial reel in the easiest way. It is attached to the spinning reel with a simple figure-eight knot or double loop. Next, the required amount of fishing line is wound. During the winding process, you need to ensure that the turns lie evenly. Ensure line tension. The easiest way to do this is with an ordinary book. The fishing line is passed between its pages, which press it, creating the necessary tension.

How to wind fishing line correctly

Let's look step by step how to wind the existing fishing line onto the reel spool. First you need to ensure that the line comes off the reel freely. To do this, you can use a screwdriver, a piece of thick wire or a regular pencil. It will be better if you do this work with an assistant. He will hold an improvised axle with a reel, and you will wind the fishing line onto the reel. The winding diagram looks like this.

You need to thread the fishing line through the spinning rings. You need to start winding the line from the top ring. Then the line must be tied on the spool. You can secure the tip of the fishing line with a regular noose loop, or wrap it with adhesive tape or tape. Reliable fastening is especially characteristic of braided cord, since it tends to “slip” at the beginning of winding. After this, you can wind the line onto the spool by lowering the line guide.

During the winding process, it is necessary to ensure that the fishing line lies with slight tension. This will prevent loops from forming.

At the final stage, all the gear should be adjusted. You need to attach a leash to the main fishing line, which will be used for fishing. You can attach the leash to the main line in different ways. Most often, anglers do this using a winding ring and a carabiner. The ring is attached to the main line, and the carabiner is tied to the leash. The leash with bait can be replaced at any time.

The process of winding fishing line onto a reel

What is backing?

This term applies only to inertia-free reels due to the specific winding of the fishing line on them.

It often happens that there is not enough line wound on the spool. For example, the spool is large, or the line is too thin. It seems that all 100 meters of fishing line have been used, and there are still 5 or more millimeters left to the sides of the spool. In this case, so-called backing is used, that is, winding up additional fishing line. This winding should be located at the very bottom of the spool. It performs only auxiliary functions and does not take part in the fishing process. But how to place it at the very bottom? To do this, you need to remove the line from the spool and then install it on the other side.

The easiest way to do this is if you have a spare spool for your reel. First, the tip of the winding line should be tied to the tip of the main line. Fastening two fishing lines does not have to be very reliable; a regular knot will do. Next, additional fishing line is wound onto the reel until a sufficient amount is wound. After this, the fishing line is secured with an elastic band, and the spool is changed.

To replace, you need to unscrew the front clamping nut, and then remove the spool and line from the reel. Instead, an empty spool is installed on the reel. The line is rewinded from one spool to another. Thus, the winding line ends up at the very bottom of the spool. If you don’t have a spare spool, then use an empty fishing line spool.

Winding braid onto a reel using backing

How much fishing line to reel

How much line do you need to put on the reel spool? Experienced fishermen always wind the fishing line not to the length required for casting, but with a large margin. This is necessary to protect against possible breaks. Also, if you are using a braided cord, at the end of the season you can swap the sides of the cord by rewinding it to the other side. This will result in savings on expensive consumables.

Typically, each reel indicates the amount of fishing line of a certain thickness that the spool can hold. Usually even several values are prescribed. For example, "0.25/200 0.30/150 0.40/100".

Advice: to prevent the line from self-ejecting from the spool of an inertia-free reel during the casting process, do not bring the winding to the very edges of the spool. It is recommended to leave a gap of 1 to 3 mm. A gap of more than 5 mm will create difficulties with casting range.

Fishing line for spinning rods from popular manufacturer Shimano

If you need to reel in a certain number of meters, you need to calculate how long the line is for 1 revolution of the spool. After this, you can roughly calculate how many turns of the handle you need to make to wind a certain amount of fishing line or cord. But you need to take into account that the number of turns of the reel handle never corresponds to the number of turns of line on the spool. For example, in most inertia-free reels, the line will make 5 turns with one turn of the handle.

Instead of a conclusion

We figured out the issue of winding fishing line or braided cord onto a spinning reel. Using this information, you can easily place the required amount of fishing line on the spool. If necessary, you can use backing if there is not enough line on the spool. If everything is done correctly, then all you can do is enjoy long and accurate casts.

The spinning tackle must be correctly selected to solve specific problems, in other words, it must be harmonious and balanced. When choosing the model of reel, spinning rod, model and diameter of the fishing line (braided cord), many fishermen do not attach importance to the correct winding of the fishing line on the reel. This guide will discuss the nuances of winding fishing line, which will allow you to avoid unpleasant moments while fishing and disappointments from the gear (dropping loops, “beard”, casting range, shooting). You will also find here step by step instructions on winding, setting up the reel and the diagram of knots for tying the fishing line to the spool.

Adjusting the winding profile (taper)

Each reel model has its own winding profile. There are:

cylindrical profile (photo 1);
reverse cone, where the profile of the wound line expands towards the front side of the spool (photo 2);
straight cone, when the profile of the wound fishing line tapers towards the front edge (side) of the spool (photo 3);
chaotic profile inherent in cheap Chinese coils.

Spinning anglers use a cylindrical or light reverse cone. The winding geometry is adjusted using adjusting washers.

The adjusting washers for reels with a front friction brake are located on the axis on which the spool is mounted, above the ratchet sprocket. The reel kit usually comes with 2 to 6 washers of varying thickness. As the thickness of the washers increases, the winding profile changes towards a straight cone, and when the thickness of the washers decreases - towards a reverse cone. If the package does not contain shims, it means they are already installed on the axle. Should be considered this moment.

Unscrew the spool by rotating the clutch counterclockwise.
Remove the spool from the reel axis (rod).
Remove (install) the required number of washers. There were cases when it was necessary to remove even the sprocket to achieve optimal winding geometry.

The adjusting washers for reels with a rear friction brake are usually located in the spool itself. The principle of adjusting the line winding profile is exactly the opposite of reels with a front friction brake. Increasing the thickness of the washers leads to a reverse cone, decreasing - to a straight cone.

To remove (install) washers you must:

Remove the bobbin.
Unscrew the special nut on the front of the spool.
Remove the shim retainer.
Remove (install) the required number of washers.

Using Backing

Becking- a layer of something wound under the main fishing line to increase the diameter of the spool so as not to wind kilograms of fishing line onto it.

The multitude of line diameters and different unwinding volumes on the market do not allow us to produce reels with a spool capacity for each type of line used. If the volume of the purchased fishing line is less than the capacity of the spool, then use rewinding under the main fishing line - backing. For backing, it is best to use an old braided cord (braid) or nylon thread, however, many people prefer just electrical tape. The volume of backing can be determined “by eye” with a margin, but in this case there is a high probability of “extra” volume of the main expensive braided cord appearing. It is preferable to add backing to the wound main line to the required level and then rewind it back. To connect the backing and the main line, you can use the following knots: “blood ties”, “grinner”, “Peter Minenko knot”, “shok leader knot”. It is necessary to wind the backing onto the spool very tightly (with force) in order to avoid the main line falling between the turns of the backing.

Tying the fishing line to the spool

Let's find out how to tie the fishing line to the spool.

The first rule is tying fishing line or backing to the spool is required. You don’t know what kind of trophy you will come across, and it will be a shame if in the process of fishing the entire main line and backing unwinds, and there is no last line to hold the fish.

The fishing line can be tied with various knots: “arbor knot”, “self-tightening double loop”, “clinch”. On the first turn of fishing line or backing on the spool, you must additionally glue a piece of electrical tape or adhesive tape in the direction of winding. This will prevent the line from spinning on the spool, both during winding and when playing fish.

How such knots are tied in practice can be seen in the video:

How to spool fishing line correctly

You need to install a reel on the first leg of the spinning rod and remove the spool. The main line must be threaded through the spinning ring and tied to the spool. Don’t forget to open the line handle before installing the spool on the reel. The line must pass through the line roller. If you have a spare spool, then this action when determining the volume of backing and the initial winding profile, it is better to carry it out with it.
The fishing line spool has a central hole, so it can easily be attached to a pencil or pen. To avoid twisting, the line should come off the bobbin as it unwinds, and not come off in coils when the bobbin is stationary. We ask a partner (children are the best helpers) to hold the spool of fishing line on a pencil. If there is no partner, you will have to adapt by holding a pencil with a spool between your knees. You can use special devices for unwinding fishing line from reels. They can also regulate the force of winding the fishing line onto the spool.
Using one hand through a rag or wearing gloves, so as not to cut yourself or burn yourself on the fishing line, we clamp the fishing line above the first ring. With this hand you can regulate the force of winding the fishing line onto the spool (as tightly as possible, but without fanaticism). With the other hand, we begin to turn the reel handle at low speed.
The volume of the fishing line being wound should be such that the fishing line does not reach the edge of the spool collar by 1-3 mm. If the volume of the fishing line is not enough, then we tie the backing to the fishing line and continue to wind it to the required volume. Winding the fishing line to the edges of the bead is fraught with loops coming off and “beard”.
After winding the line and backing to the required level, it is necessary to rewind the line from the spare spool to the main one. If the line winding profile is unsatisfactory, you can adjust it by removing or adding the necessary adjusting washers. If there is no spare spool, then for the final winding of the fishing line you will have to rewind the fishing line either to another reel, or first to one reel, then from it to the second reel. This is necessary to turn the line over. For these purposes, you can use a drill by attaching bobbins to the spindle.
After the final winding of the fishing line onto the spool, we attach the edge of the fishing line to the clip, which is located on the side of the spool.

Compliance with simple principles: the use of backing, the correct force, profile and volume of winding will allow you to obtain optimal use of the gear and ensure working with it at a high level of efficiency.

Winding a line onto a reel is one of the main keys to successful fishing, since if the winding system is incorrect, the line fiber gets tangled or torn off. It is for this reason that you need to know the correct winding systematics, as well as be able to use special devices that can make this task easier.

Winding profile

Different reel models have specific profile shapes or profiles. There are several profile forms:

cylindrical profile shape;
reverse cone shape, having an expansion in the direction of the front bobbin edge;
straight conical shape, tapering towards the front bobbin edge;
chaotic profile shape, which is found on almost all Chinese reels that have a cheap price.

Adjusting the profile is quite easy if you follow the correct order and also know all the subtleties of adjusting the coil profile. Typically, a cylindrical or reverse conical profile shape is used for spinning. Using these species as an example, we will consider the systematics of regulation.

First view

The adjusting washer of the reel with a front type brake friction system is located on the axis, having a bobbin mechanism mount, as well as above the sprocket-ratchet device;
Reel kit includes from two to six washers of various thicknesses;
Increasing the size of the washer, the profile winding ratio changes towards a straight cone shape, and as the size of the washers decreases, the change occurs to a reverse cone type shape.

Unscrew the bobbin mechanism, in this case the clutch should rotate counterclockwise;
The bobbin mechanism is removed from an axial location;
Install or remove the required number of washers, in this case, it is possible to remove the star-ratchet device, since there is a need for an ideal geometric position.

Type two

Adjusting washer using rear friction brake in the usual location it should be located in the bobbin device itself;
Adjustment is reverse to the front brake system, that is, as the size of the washer increases, it moves towards a reverse conical shape, and with a decrease, it moves towards a straight conical shape.

Installing or removing the washer requires:

The bobbin mechanism is removed;
the special nut in the foreground of the bobbin device is unscrewed;
the locking mechanism of the adjusting washer is removed;
the required number of washers is removed or installed.

The reel kit includes from two to six washers of various sizes and thicknesses

Application of backing

A backing device is a layer-by-layer application of some material onto a base, onto which a fishing line is subsequently wound. It is required to increase the bobbin diametrical cross-section, and this saves fishing line, since numerous turns are not required.

Backing is necessary due to the fact that the volume of the bobbin device cannot be suitable for all types of forest fiber. Thus, when the volume of fishing line is less than the capacious bobbin size, a winding device is used for the fishing line base in the form of backing.

Several materials are used as backing:

braided cord;
nylon thread;
durable electrical tape.

The usual use of backing is to add it to the winding to the required level, after which further rewinding continues.

Winding is done with increased density so that a gap does not form in the line base. Several forms of knots are used for attachment to the fishing line fiber:

blood ties;
grinner;
Peter Minenko's node.

Winding is done with increased density so that a gap does not form in the line base

How to tie fishing line to a spool

Tying a backing device or line fiber to the bobbin device is mandatory, as this avoids the loss of a large fish specimen, as well as spinning the line fiber on the bobbin device when winding or fishing for fish. Additionally, electrical tape or a regular piece of plaster is glued in the direction of winding.

Binding is carried out:

using a self-tightening double loop;
using a clinch;
using similar nodes, but the best options are the first two types of nodal form.

Winding fishing line: do it right

Winding of forest fiber must be carried out in compliance with certain rules. In addition, the correct order of winding systematics must be observed:

A reel device is installed on the first-generation spinning part, and the bobbin mechanism is removed.
The fishing line reel is equipped with a central hole, which allows it to be easily attached to a pencil or pen rod.
To avoid twisting, the fishing line fiber, when it comes off the bobbin, unwinds the latter, since the fishing line cannot be pulled from a stationary bobbin. The second person must hold the reel on the pencil base; if this is missing, then the pencil rod is clamped with the knees. To unwind fishing line from a reel, special purchased units are often used, which can also adjust the winding forces of the fishing line fiber onto the bobbin mechanism;
The fishing line fiber is clamped with a gloved hand (so as not to cut your fingers) higher than the first ring.
This hand will be engaged in adjusting the winding forces of the line fiber onto the bobbin device, while the other hand turns the spool lever slowly and steadily;
The volumetric size of the wound line fiber should not reach the bobbin side by two to three millimeters. If the required line volume size is not available, a backing device is attached to the line, after which winding continues to the required limits. The line is not wound to the very edge, as the loops subsequently come off in the form of a “beard”;

When winding of the line fiber and backing device is completed to the required strip, rewinding is carried out from the spare bobbin device to the main one.

If the profile does not meet the requirements, then adjustment is made using shims. In the absence of a spare bobbin device, it is necessary to rewind the line fiber to a secondary reel, which is a reserve, or to a bobbin, since the line fiber must be turned over. Drills are often used as a rewinding device, on the spindles of which the bobbin can be secured;
After winding the fishing line fiber onto the bobbin device, the end of the fishing line is attached to the clip protrusion
, which is located on the side of the bobbin device.
Optimal use of gear and ensuring uninterrupted operation is possible when the entire system is executed in the correct order, as well as using certain rules and schemes, that is:

backing application;

correct amount of force;

The reels can be different, since there are several types of reel types, and this changes the nature of the winding. For example:

Cartoon type reel cannot change the bobbin part, when filling forest fiber or backing that was produced in advance;
The inertial type is distinguished by the difference in possible bobbin devices, and this leads to the fact that the change operation will also fail;
Inertia-free type easily changes spools with braids or fishing line.

Thus, winding on a spinning reel is simple, but the other two types have differences.

The inertial type of coil has a number of features:

A regular coil has a volumetric size one hundred meters of forest fiber;
Spinning rod or feeder with pass-type rings, have a peculiarity in winding the fishing line onto the assembled rod;
With the spinning rod unfolded, the line fiber is passed through each passage ring, starting with the smaller one, while the line-laying bow is bent, after which the line fiber is secured to the bobbin device using a knot or a locking device. A certain number of turns are made in a measured, slow manner by hand, after which the lever or handle is turned, and the fishing line fiber will be wound.
With the correct winding form, the fishing line fiber should lie according to the example spool of thread, that is, without gaps and in a dense format.

The multiplier type of reel has only one feature. The scaffold fiber must have a diametrical cross-section that is intended for the model in question.

The spinning reel also has a list of features in direct use:

The size of the fishing line thickness should be equal to that, which is indicated on the reel mechanism, since with a different diametrical cross-section of the fishing line fiber there will be difficulties with threading;
Each spinning reel mold is created for a specific fiber diameter, in addition, the volumetric size of the backing is also limited;
All coil parameters are indicated in the passport data, with each manufacturer corresponding to different data;
Line winding on an inertia-free type of reel is made with dense turns to each other or in a cross-shaped manner.

There are a number of rules for correctly winding forest fiber onto the reel base; in addition, there are several useful tips, which will help facilitate this process:

Determining the depth or volume of unwound line fiber can be measured by a counter, which is installed in a cartoon type reel format, without a counter you can simply mark the fishing line with a special marker every meter or two;
There are several simple rules for good winding: there should not be a large nodular shape, it is impossible to weaken during line winding (the same force throughout the entire length of the line force), the first turn is the most important, since the entire further winding path will depend on its position;
Buying cheap fishing line or reel base may not be justified, since the line form of fiber may vary in quality, and the reel may turn out to be defective, that is, it is worth buying gear with good quality, since this, on the contrary, will save money and nerves;
There is a trapezoidal coil profile, it uses the principle of a reverse cone type, that is, the winding goes on different sides in a conical shape.

This is a fairly simple action that any beginner can do. Necessary unscrew the fastener And insert the coil in a special holder on the spinning rod handle. After this it is necessary tighten the ring so that it presses the base of the coil. It should be screwed tightly so that the coil does not dangle.

However, do not use excessive force to avoid stripping the threads, which are made of plastic.

How to wind fishing line

To do this, you must perform the following steps.

Pull the tip of the line through the spinning rings, starting with the smallest one located at the top of the rod.
Fold out the line guide ring and tie the line onto the spool. This is best done using a special self-tightening knot.
To make it, you need to make a double loop and tighten it on the bobbin. The protruding end of the fishing line must be cut off.
Next, you need to correctly wind the fishing line onto the spool. To do this, you need to create a slight tension. It is convenient to wind the fishing line with a partner who holds the reel with fishing line in his hands and controls the resistance. If you don't have an assistant, you can do it yourself by putting the spool in your pocket.
You can also pass the line through the fingers of the hand with which you are holding the spinning rod, and rotate the reel handle with the other.
It is also not worth creating excessive tension, as this can lead to the formation of knots and uneven winding.
It is recommended to reel in the line without stopping and constantly monitor the process.
The winding process must be completed at the moment when approximately 25-30 millimeters remain to the edge of the spool. This is considered its optimal filling. It is not recommended to reel in any more fishing line, as this can create some problems (the appearance of knots, the line jumping off the spool when casting).

Helpful advice! After finishing fishing, you need to make one single cast. In it, raise the rod perpendicular to the ground, and slowly rotate the reel handle to wind the fishing line. This will allow it to dry and be placed correctly on the spool. A nice bonus in such cases can be a bite, which happens quite often!

How to set it up correctly

This is probably main point in the preliminary setup of your spinning rod. A lot will depend on him.

Correctly tuned coil will prevent line breakage And allows you to catch big fish.

Almost all inertia-free reels are equipped with a friction brake, which allows you to adjust the force.

At a certain load, the spool begins to scroll and release the line. This is necessary to “dampen” the jerks of large fish.

There are two types of positioning of the regulator - on top of the spool and on the bottom of the reel. The second option is practically not used in new models, although it is quite common among spinners.

It is necessary to adjust the friction based on the breaking force of the fishing line. For example, if it can withstand a real 7 kilograms, then the friction brake needs to be adjusted to 4-5 kg. This will allow, in the event of a fish jerking with a power of 7-8 kilograms, to keep the fishing line safe and release it into the reservoir under the pressure of a predator. To do this, you need to fill the bobbin completely.

3 ways to increase your fish catch

There are many ways to increase your fish catch, but the most effective ones are. Below the site editors share with you the 3 most in effective ways increase in catch:

. This is a pheromone-based additive that activates receptors in fish. ATTENTION! Rybnadzor wants to ban this bait!
Any other baits with flavorings are less effective; it is better if they contain pheromones. But it’s most effective to use new 2016 — !
Learning different fishing techniques. For example, it is written about spinning wires.

To adjust, you can use weights from ordinary scales, which are hung on the end of the fishing line. Experienced fishermen adjust the drag a little differently. This can be done directly while fishing.

Fully equip the spinning rod and hang a spinner on it.
Hook it on a tree or other object.
Move 5-10 meters away and pull the spinning rod as if you were fishing for fish.
Apply maximum tension (the rod should bend into an arc), and gradually release the clutch until the ratchet operates.
You shouldn't pull too hard, as you can break the rod.

As you can see, there is nothing complicated about attaching a reel to a fishing rod and setting it up, and any beginner will have to perform these steps.

But it is very difficult to overestimate their importance, since success in winning a large trophy may depend on it. Happy fishing!

Watch the video to learn how to wind the fishing line onto the spool. Enjoy watching!