Do-it-yourself hook for a bottom fishing rod. A simple hook for bottom tackle

Quite often when fishing, fishermen use bottom gear, but if the bottom is equipped with a rod, then it is very difficult to hold such a rod in your hands for a long time. In order for the angler to still have the opportunity to leave the donka rod for a short time, cunning fishermen invented a hook hook for the donka.

What is the purpose of a bottom hook?

The hook hook for the donkey is designed to ensure that the angler has his hands free while fishing; moreover, with the help of such a device, the angler has the opportunity to calmly catch fish on several donkeys at the same time, which is very convenient and comfortable, among other things, to a large extent increases the chances of catching.

Thanks to the use of such hook hooks, it is possible to automatically carry out the process of hooking fish without the participation of the fisherman himself, because this device itself makes an automatic jerk for hooking instead of the fisherman. Such devices are sold freely in fishing stores; besides, fishermen have learned to make such self-hooking devices themselves with their own hands at home.

Types of self-cutters for donkeys

It should be noted that hooks can be mounted on almost any fishing device - donks, feeder rods, float rods, spinning rods.

In this case, fish hooks can be mounted either on the rod itself, or next to this rod, when the fishing line is tensioned with an elastic band. Among other things, for this you will definitely need a paper clip for the lever or wire. A fishing line is attached to one side and an elastic band to the other end. The lever itself is made in the first ring of the fishing rod.

Among other things, you can mount the hooker on a leash when the hooking process is carried out in water. In this case, the cutting mechanism is created with a base of elastic or spring. When a fish bites, a process is carried out to release one of the tense ends of the lever. After straightening the lever, a sharp cutting jerk is made.

Moreover, both of these options make it possible to ensure the process of increasing the fisherman’s catch to a significant extent. It is worth noting the fact that fishermen are constantly improving such devices, making them more convenient and comfortable to use. At the same time, undercutters are improved from ready-made devices, or new devices are made.

Today, there are several main automatic hook hooks. The first option is an improved tackle, where fishermen make special changes to the design of the hook with a float, as a result of which the hooking process becomes automatic without the participation of the fisherman himself.

There are also homemade versions of hooks, which are based on the operating principle of a mousetrap, where either an elastic band or a spring is used. There are also options for industrial hooks that are created for a specific type of gear. Most fishermen still buy ready-made options and finish them in their own way.

Do-it-yourself self-cutter for donkey - materials and tools

To make a bottom undercutter on your own, you should prepare in advance the following set of components necessary for this:

• - the rod itself and the mount that will hold the rod;
• — a fastening device to connect the bracket and the main part, this mechanism will be responsible for the process of lifting the fishing rod;
• — you will also need a rear bracket and a spring with a certain power;
• — the presence of shock-absorbing rubber is required;
• - holes should be made in advance on the main part of the fastening;
• — you will also need a bracket axis and rubber, which will be attached to the bracket body;
• -you will definitely need a trigger made of steel, which has a bend at the top so that the bracket can jump off when cutting;
• - you will also need to attach the bracket to the main part;
• - fishing line with reel;
• - tackle

In this case, the future structure will be fixed to the ground, and the sensitivity parameters will depend on the trigger.

You should also initially prepare:

• - aluminum plate;
• - wire with diametric parameters of approximately two millimeters;
• - plate made of hardened metal;
• - pliers and wire cutters;
• — rubber and spring;
• - a screwdriver and plastic, for example, computer disks;
• - aluminum rod and clothespin;
• - bolts and nuts.

Do-it-yourself self-cutter for donkey - how to make it?

Initially, we bend the aluminum plate in the shape of the Russian letter P, the sides of which will be two centimeters each. Next, you should drill a pair of holes with a diameter of about two millimeters on each side of the bent plate.

Next, several turns are wound, about three turns each, onto a hardened plate, which plays the role of a spring. Bend the tip of the wire into the shape of a large hook. Place the wire in an aluminum plate, insert a spring, and attach a cambric to the other opposite end, which acts as a retainer. Bend the tip of the wire.

Next, the long tip of the spring is wrapped in a loop around the wire and the mechanism is secured to the tip of the board, but so that it touches the guard. Using several self-tapping screws, you should attach the plate to a wooden plank. The device is ready for use.

1. When installing a hook hook for automatically hooking a fish, the fisherman should be very careful and careful, because the tension is large and strong. If you jump off carelessly, you can get injured.
2. When fishing in calm water, experienced fishermen recommend setting the self-hook to its minimum effort; this circumstance will greatly increase sensitivity.
3. To attract more fish, some anglers use rubber bands with feeders.

Fishing - a great form of recreation, but it takes a lot of time to be on the shore and hold a fishing rod in your hands. Fishermen often go out to eat, chat with friends or just relax. And at such moments the fishing stops. To be able to sometimes move away and not watch the bite, automatic hookers were invented. One of them -self-cutter for donkey.

If used when fishing some , or the fisherman is simply distracted, you may miss the moment of a good bite.This is where they come in handyself-cutters for donkeys. They will be able to hook the fish in time without the participation of the fisherman - the structure will make an automatic jerk. Fishing experts are able to dodo-it-yourself hook for bottom fishing rod.

Types of automatic undercutters

Such devices can be installed on any fishing rod. Most often they are installed on simple hooks, feeders or fishing rods with floats.An automatic hooker for spinning becomes appropriate if a feeder tackle is installed on the rod.

Automatic undercutters can be installed:

1. On or near the rod. With this option, the fishing line will be tensioned using a rubber cord. If you don't have one, a simple rubber band will do. You will also need steel wire (or a simple paper clip) to make the lever. A fishing line will be attached to one side of it, and a stretched rubber cord to the other. The lever will be located in the first ring of the fishing rod. If the line pull is horizontal, the lever will pop out of the ring. Then the elastic band will contract, and the fishing line will stretch behind it.
2. On a leash. Hooking takes place right in the water. The hooking mechanism will be created on the basis of rubber or spring. At the moment of the bite, one of the tense ends of the lever will be released. After the lever straightens, it will make a sharp jerk, and the fish will be out of the water.

Both options allow you to increase your fish catch several times. The main thing is that the mechanism for their operation is installed correctly.

Fishermen are constantly improving designs, making them as convenient as possible for their fishing rods. Some make them with their own hands from available materials, others buy ready-made undercutters to modify the mechanism.

There are several types of automatic cutters:

1. Improved tackle. Some changes are being made to the design of the hook and float, thanks to which the hooking will be automatic.
2. Homemade design. A self-made automatic hooker is similar in principle to a mousetrap: its movement is based on either rubber or spring.
3. Industrial undercutters. These designs are made for specific gear.

Anglers can buy an industrial kit and customize it as they wish.

Do-it-yourself self-cutter for donkey

To assemble the mechanism you will need:

1. Fishing rod;
2. A mount that will hold the fishing rod (consists of two parts - the front bracket and the main part);
3. Fastening part (connects the bracket and the main part, is responsible for lifting the fishing rod);
4. Rear bracket;
5. Spring of a certain power;
6. Shock-absorbing rubber;
7. Holes on the main part of the mount;
8. Shackle axis;
9. Rubber that is attached to the bracket body;
10. The trigger is made of steel (with a bend at the top so that the guard can slide off when cutting);
11. Attaching the bracket to the main part;
12. Fishing line;
13. Coil;
14. Tackle.

The entire structure is fixed in the ground. Sensitivity will depend on the trigger.

Materials

List of tools and materials for manufacturingself-cutter on the donk:

1. Aluminum plate;
2. Wire with a diameter of 2 mm;
3. Tempered plate;
4. Wooden plank;
5. Pliers;
6. Screwdriver;
7. Wire cutters;
8. Rubber or spring;
9. Plastic (computer disks are suitable);
10. Aluminum rod;
11. Pin;
12. Bolts and nuts.

Naturally, you need to prepare the rest of the necessary fishing attributes:

• Rod;
• Hooks;
• Bait;
• Fishing line;
• Coil.

Manufacturing

1. Bend the aluminum plate into the shape of the letter U with sides of 2 cm.
2. Drill 2 holes with a diameter of up to 2 mm on each bent side.
3. Wind approximately three turns of wire onto the hot plate. It will act as a spring.
4. Bend the end of the wire so that it is shaped like a large hook.
5. Install the wire into the aluminum plate and put on the spring. Put a cambric on the opposite end. He will be a fixer. Bend the end of the wire.
6. Now you need to wrap the long end of the spring in a loop around the wire.
7. Secure the mechanism at the very end of the board along with the wire ring.
8. Position the folding structure so that it touches the gatehouse.
9. Using several self-tapping screws, attach the plate to a wooden board.The structure is ready.

1. When installing an automatic undercutter, you need to be careful and careful. The cutting force, rubber or spring tension is always high. If the runner comes off the base, there is a risk of injury.
2. If the water is calm or the current is minimal, it is recommended to set the trigger force to minimum. This will increase sensitivity.
3. To attract more fish to the bait, you can install a rubber band with a feeder.

Other solutions to the problem

There are also options invented by ordinary fishermen. One of them is an automatic float cutter. It goes like this:

1. The upper antenna is pulled out of the float.
2. You need to put a foam ring on it. The ring size is slightly larger than the antenna.
3. Now you need to return the antenna to its place.Attach a bead to the top.
4. During the bite, the ring will not allow the float to sink to the bottom, and the fish will be hooked.

An automatic hooker is indispensable if your fishing goes on for a long time and you want to relax, but at the same time not lose your catch.

Making a hook for a bottom fishing rod with your own hands is not so difficult. But here a reasonable question arises: what is it for? After all, all the fun of fishing lies in hooking and landing fish. Here it is worth understanding the purpose of a hook hook for a bottom fishing rod as an aid when fishing using several rods.

Often when bottom fishing you have to place rods at a decent distance from each other due to a certain terrain.

In such a situation, an automatic undercutter will serve well. You will be able to do something while fishing. For example, if you need to reconfigure one of the gears in case of a break.

The auto-cutter circuit is quite simple. A typical drawing can be found on the Internet. If you still decide to make an automatic undercutter, pay attention to its design.

1. The first ones are installed directly on the rod or nearby. Their essence is to tension the main line using a rubber cord. If it is not available, you can use several bank (stationery) rubber bands. A small lever is made from steel wire (an ordinary paper clip will do). A fishing line is attached to one side of the lever, and a rubber band under tension is attached to the other. The lever is located in the first ring of the rod. When the fishing line is pulled horizontally, the lever pops out of the ring. Next, the elastic band begins to contract, dragging the fishing line along with it.
2. In the second method, the cutting mechanism is placed on a leash. Auto hooking occurs directly in the water. The essence of the method again comes down to the spring mechanism. When biting, the fish releases one end of the lever, which is under tension. Straightening up, the lever makes a sharp jerk on the main line, thereby hooking the fish.

Auto hooker will help increase your catch. It will work faster than you are near the rod.

It should be noted that fishermen have been using various automatic hookers for a long time. Most of them are developed by folk craftsmen. Although it is already possible to purchase these factory-assembled mechanisms on international Internet sites.

Mention should also be made of interesting species invented by the people.

• in this case, the upper antenna is removed from the float;
• a homemade foam rubber ring with a diameter slightly larger than the thickness of the antenna is put on it;
• then the antenna is glued into place. The ring should move freely along the antenna;
• a bead is attached on top;
• When biting, the ring prevents the float from plunging into the water, hooking the fish.

If the fish rises, this method will be useless.

Today we offer the topic: “self-hook for fishing” from professional fishermen. We tried to cover the topic as fully as possible. You can ask all questions in the comments after the article.

In fishing practice, there are devices that make this process easier. A self-hooking hook for a feeder is a simple design that allows you to place a fish on the hook of a bottom tackle without the participation of a fisherman. All that remains for him is to release the fishing line from the grip and bring the trophy ashore.

The main task of an angler when biting a fish is to hook it in time. When bottom fishing, you must, firstly, accurately see the twitching of the fishing line or the guard, and secondly, raise the rod and give it a small jerk. If the fisherman has good reaction and dexterity, he successfully gets a trophy on the hook. All that remains is to fight.

However, there are circumstances when constant monitoring of a fishing rod or donkey is either impractical or impossible. For example:

• the fisherman uses several gears;
• bites are rare, and there is no need to constantly monitor the fishing line;
• fishing occurs at night.

Self-hookers for fishing serve precisely to shift the responsibility for timely hooking to the automation. These devices must quickly respond to bites, and also at the right moment sharply pull the fishing line with the proper force. The fisherman does not take part in this process.

The principle of automatic hooking is used most often in bottom fishing; in float and spinning gear there is no need for it, since the angler here must constantly monitor the position of the nozzle or bait.

There are several designs of this device, there are those that are produced industrially, there are auto hookers made by fishermen based on their developments.

All existing devices of this kind can be placed in two ways:

The rod immediately behind the reel after casting is folded at 90 degrees, the handle is fixed in the holder, most of it is directed towards the water. When a bite occurs, the fishing line pulls the trigger or bracket, the spring is activated, and the autohook sharply lifts the rod vertically. At the moment of straightening, cutting occurs.

This option requires a very light rod and its working length is no more than 2 meters. Otherwise, the spring will not be able to lift the form and sharply pull the fishing line.

The mechanism has two drawbacks. Firstly, it is made of ordinary steel and is susceptible to corrosion. After each fishing, it must be wiped dry and thoroughly lubricated. Secondly, the spring loses its elasticity over time and you have to either look for a replacement or transfer it to a coil.

The principle of operation is similar to the previous one. Only here the entire form is fixed on a special bracket, which lifts it vertically. The mechanism is triggered after a sharp tension of the fishing line hooked to the trigger.

3. In the immediate vicinity of the feeder, on the shore along the line.

The device operates like a mousetrap and is made by fishermen themselves. In the next chapter we will talk in detail about the stages of its creation.

Constructions of the first and second types are manufactured industrially.

They are easy to install and do not require complicated installation. However, fishermen are not satisfied with one significant drawback: such a mechanism is usually configured for a specific gear and power adjustment is possible within limited limits. A cautious bite is not recorded.

The first two types of devices are difficult to manufacture independently. Therefore, a do-it-yourself self-cutter for donkey is made mainly of the third type. The fisherman is then able to pre-design and select the required force to trigger the device. The mover here can be either rubber or a steel spring.

The purpose of designing undercutters for a feeder is usually summer tackle. The design of the device for winter fishing is similar to the one under consideration, but requires improvement.

Having determined what kind of fish and with what temperament to catch, they first make drawings of the device, and then begin to make a self-hooking fishing rod with their own hands.

The process is divided into the following stages:

The entire device will be located on this platform, so you should choose sheets with a thickness of 10 mm or more. Subsequently, holes are drilled in the base through which pins are threaded that secure the platform to the shore.

The most successful form of undercutter is a slingshot, which does not have sharp corners or edges. A spring is wound onto the resulting lever, the material for which is steel wire with a diameter of up to 1 mm (the best performance is for wire made from a thick cable). This is done manually; with one hand, using pliers, the spring wire is clamped with a lever, and with the other, the wire is wound tightly, turn to turn. It doesn't matter which way you twist it.

Since it is this element of the mechanism that will sharply tighten the fishing line, you should carefully experimentally select the elasticity of the spring, adding turns gradually, since it is very difficult to reduce the size of the spring. The power of the device should be greater, the heavier the load at the end of the tackle. At the end of the procedure, you need to leave a section half the length of the lever, and 5-7 cm on the other to secure it from turning.

The material used for it is the same as for the main lever - steel wire 3-4 mm in diameter. If you plan to take thinner material, then the stiffer it is, the better. The bending profile is visible in the photograph.

Most often, the fishing line is passed through a rubber or silicone tip. It has been learned from practice that an ordinary stationery eraser cut into two parts shows good results in this capacity. To be sure that it will not fall off with frequent use, you can reinforce it with bright electrical tape.

The bracket is attached to the base with staples made from nails without heads.

Its shape is up to the fisherman. Most often it is made in the form of an inverted letter “P”. Two holes are drilled in the base for attaching it to the base, and in the sides for installing the lever. There are two ways to fix the spring, but the most practical is the console shown in this photo.

With what pleasure do fishermen hook fish when, sitting on the shore in good or bad weather, they implement their hobby with sporting passion. Emotions, adrenaline, rich catch! All these are components of successful fishing. But what to do if you need to step away from the gear for a while, have a quiet lunch and relax? This gear is designed for such a case. An automatic fish hooker is very necessary when there is no time to constantly monitor the fishing rod and watch for a bite.

Homemade product at work

Self-cutting device with aircraft tires

In one of the simple and at the same time effective self-cutters presented below, the basis of the mechanism is aviation rubber, a plastic profile, a piece of plastic from a DVD or CD, an aluminum rod, an M6 bolt, two nuts (you can also use a wing, it’s more convenient), pin. As you can see, to make a do-it-yourself undercutter you don’t need scarce materials; you can assemble it from the parts you have on hand.

When fishing for fish using a self-hooking hook, you can use a donkey without a rod and with it, by attaching a device to it. After casting the fishing rod, you need to release the line a little and insert it into the slot of the guard.

Now the auto-cutter is even simpler in design and operation, and how does an undercutter work?. This device works great in currents, is easy to use and can be used at any time of the year.